Combine Heat and Power CHP Wood Gas / Pyrolysis Gas Generator 300kw - 2MW

• Customization: Available
• Output Type: AC Three Phase
• Gas Source: Gas
• Power: ＞200kW
• Standard: Standard
• Power Usage: Daily Usage, Industrial Usage, Sell to Grid
• by Products: Hot Water for Heating House, Hot Steam
• Gas Pressure: 3-20kpa
• Lube Oil: Otal Gas Engine Oil 15W-40
• Lubrication Mode: Pressure and Splash
• Warranty: 12 Months
• Cooling Mode: Closed or Open Type Water Cooling
• Installation Abroad: Yes, Guide Installation
• Alternator: Siemens: Brushless, with AVR, Insula
• Controller: Comap, Deepsea
• Transport Package: Plywood Case 20/40gp Standard Container
• Specification: Composition: CH4
• Origin: China
• Production Capacity: 5000sets/Year

Product Description

 

Combine Heat and Power chp Wood Gas / Pyrolysis Gas generator 300kw - 2mw

1. Combine Heat and Power chp Wood Gas / Pyrolysis Gas generator 300kw - 2mws
1) Low cost in maintenance
2) Large cylinder , Long Stroke, Low Speed, which means big reserve power capacity and constant power output
3) Low Engine Speed at 500 or 600RPM
4) Naturally Aspirated, which means low failure rate and minimaldowntime
5) Internal MixingSystem (for high hydrogengas)
6) Strong Treatment and Resistance AbilityAgainst TAR
7) Long Overhaul Time of 60000hours and lifecycle of 20-25 years
8) CE and ISO approved
 
2. Main technical parameters for Combine Heat and Power chp Wood Gas / Pyrolysis Gas generator 300kw - 2mw:

Syngas Engine	Item	Technical specifications
	Model	6300D/M	8300D/M-1	8300D/M-2
	Type	In-line, four-stroke, inter-cooling, spark plug ignition, open combustion
	Cylinder number	6	8	8
	Cylinder diameter (mm)	300
	Rated speed (r/min)	500	500	600
	Rated power (KW)	400	500	550
	Heat consumption at rated power (MJ/kwh)	≤11.0
	Rotating direction (from flywheel side)	Clockwise
	Starting mode	Compressed air/motor start
	Exhaust temperature (ºC)	≤600
	Gas pressure (kPa)	≥2.5
	Gas inlet temperature (ºC)	≤40
	Oil consumption rate (g/kW.h)	≤0.8
Syngas Generator set	Model	350GFM	400GFM	500GFM
	Rated power (kw)	350	400	500
	Voltage (V)	400/6300/10500
	Current (A)	631/40/24	722/46/28	902/57/34
	Power factor (COSΦ)	(lagging)
	Excitation mode	Brushless
	Phase and connection	3 phase 4 wires/3 phase 6 wires
	Size (L*W*H) (mm)	5800*1600*2900	6400*1600*2900	6400*1600*2900
	Weight (kg)	18000	22000	22000

3. Environment requirements for Combine Heat and Power chp Wood Gas / Pyrolysis Gas generator 300kw - 2mw:
1) Ambient temperature between -20°C~+40°C;
2) Relative humidity less than 90%(20ºC);
3) Site elevation not higher than 2500m;
4) For outdoor installation, simple rain shelter is required. 

4. Combine Heat and Power chp Wood Gas / Pyrolysis Gas generator 300kw - 2mw gas quality requirements
1) Gas temperature≤40°C
2) Gas pressure 2.5~10kpa, Pressure change rate≤1kPa/min
3) Tar content≤20mg/Nm3
4) H2S content≤50mg/Nm3
5) Impurities particle size≤5μm, Impurity content≤30mg/Nm3
6) Moisture content≤20 mg/Nm3
7) Heat value≥4MJ/Nm3.

Service 
 
1.pre-sale service:
(1)We will send our engineer to prospect the site of power station free to charge.
 
(2)According to the situation of site we can supply you many drawings:like power station floor plan,
engineering flow sheet of circle cooling system,genset installation,genset foundation,electrical connection and some other techincal support etc.
 
2.Sale service:
(1)we will send our engineer to the site to guide you the installation of generator set, subsystem and relative equipment.
 
(2)We will debug the generator set till it can generate power successfully.
 
(3)We will also supply a technical training to the operators.Orcan send your staff to our company.We can train you till you can operate the generator set.
 
3.After-sale service:
(1)Our every engineers are in charge of different area,we will response periodically and support you 
technical service free of charge,
 
(2)For the quality problem, we will service for you free of charge during the guarantee period.
 
(3)One year guarantee period and lifetime service.
 
(4)we solve quality problem in time when genset doesn't work,We insure to help our clients to gain the biggest economic profit.
 

FAQ:
1.How to choose the right model? 
A: It depends on real output power, Voltage, Frequency and gas type.  
2.What is the oil consumption and capacity per hour? 
A: 1.0-1.63g of lubricant oil consumption per hour. 1.0 Cubic meter gas can produce 1.5-3.0kw/h power. The capacity depends on gas energy. E.g 1.0 Cubic meter natural gas produce about 3.0kw/h  
3.What is the overhaul? 
  A: About 30000 working hours. A week is enough to finish.  
4. What is the warranty? 
    A: 1 year. Inside this 1 year, we offer all spare parts free of charge. After this period, spare      parts are not free. But, a set of spare parts will be shipped together with machine free.  
5. How is the service? 
A: We offer installation,repair and maintain service abroad. And online guide service if needed anytime. Our before-sale, in-sale and after-sale service are all trustable, you can name it.